This project was definitely easy, took about an hour of actual work time and had minimal pain in the #$%  annoyances.

Do learn from my mistake, take a staple that works in your staple gun to the store so you buy the right size, nothing like a hardware store run to kill your project mojo.

Tools

Wrench – the screws that held the tabletop to the frame had no slot or philips head, just a hex. So a bit of a pain, still minor.

Small flat head screwdriver – to remove staples

Scissors

Staple gun with 1/4″ staples

Hammer

Supplies

Chalkcloth 1″ bigger all the way around then the table top, mine was 33.5″ so I used a 36″ sq of chalkcloth

1/4″ staples (tabletop is 1/4″ hardboard)

Prep

Cut Chalkcloth to size and make sure all the wrinkles are out of it.  Easy way, lay it out in the sun on a warm day, it will amaze how soft and pliable it becomes, or use a hair dryer ( a warm iron, iron backside with a pressing cloth – but pay attention to what you are doing, this could ruin your project before you even start- but hey I know how you roll- I live on the craft edge too).

Flip your table over and remove the top.  The screws on mine had to be removed with a wrench to grab the hex top, a little more effort than using a screwdriver and slightly annoying, but there are only 12.

Take the flat head screwdriver and pry off all the staples to remove the previous vinyl.  Have a vaccuum handy they can fly about and they hurt when stepped on – another mistake of mine.

Now on a hard surface – not carpeted – lay down your flat piece of chalkcloth and center the top.  Cut a little bit away at the corners, follow the curve of the tabletop.  Why hard surface?  Keeps the chalkcloth from shifting and more importantly lets the staple  gun do its job ( started out on carpet and learned the lesson quickly).  The tabletop cannot have a soft/bouncy surface that will absorb the force of the staple otherwise ZERO staples will go in the board (another lesson learned by me for you).

Time for some power tool fun!  Start stapling along one side – complete it then do the opposite side.  The chalkcloth has no give so there is no need to do the typical upholstery technique.  Just pull it taunt when you start the opposite side just to make sure the wrinkles are out.  Then do the other two sides.  The corners need little pleats, big pleats  staples will not go in, plus it looks better and lies flatter with little pleats.

Take the hammer and give all the staples a little tap to secure a bit better.  Rub your hand around the edge just to make sure none of the staples got to close to the edge and are poking out – another lesson learned.

Flip it over, take a peek  – looks good.  Time to add the frame back. It will take a little persuasion, but the frame will fit over those clips.  Then reattached with the screws.

Set it up and TaDaa!  Fab new chalkcloth card table!

Give it a try!

We’ve come up with some great downloads to create your own palette card from all the bits and pieces of felt you purchase and the little extras we include in every shipment.

TaDaa Studio DIY Felt palette card PDF download

Plus we have one without all the names so that you can create your palette of what’s in your stash for easy inspiration.

TaDaa Studio DIY Blank Felt Palette Card PDF download

source Country Living Nov. 2011

The newest colors are….

Blue Snow…Beach Sand…Pea Soup…Native Maize…Wisteria..Mac’n'Cheese

I let him choose the colors and paint a door himself.  He wanted to keep the white frame so that it would match the other doors, but otherwise thought a tie-dye look would be most fitting.

He leaves stones, feathers and other treasures he has collected from outside to entice the gnomes to take up residence in his bedroom.  If that doesn’t get them coming to visit, he says he’ll leave them chocolate.

I’m sure the fairies will approve and will gladly make room for the gnomes.

The ladies purchased the DIY fairy door kit, brought their paints, wood stains and embellishments to Lyndsey’s house and spent a fun night creating unique fairy doors to compliment their new homes.  Take a look and be inspired.  What a great way to give each other a send-off and to create a memory of their years together.

What a busy past couple of months!  We have all kinds of exciting news and fun new projects to share with everyone this spring.

We’ve kicked off the year in a big way with filming a TV segment for a new PBS show, It’s Sew Easy.  The episode will feature our wool felt baby grab ball. Remember those from childhood?

It was an amazing experience to be on TV and to meet the other designers who were filming with us.  Check out the studio!  More details on the show coming your way soon.